超高壓大口徑氣動球閥是氣動執行器的一種新産品，它具有新穎獨特的結構和專門的控制系統設計，它與氣控或電控組合儀表配套，廣泛地應用于冶金、礦山、石油、化工、電力、輕工、船舶等工業部門和自動化控制系統中，适用于氣體、液體或含有懸浮顆粒流體的流量控制或切斷。它能适應模拟量或開關量兩種信号控制，實現快速開關動作。具有流阻小，開關迅速、啟閉靈活、壽命長，安全可靠等優點。
The pneumatic ball valve made by CHV is new designed, which has unusual construction,and special control system. It can be combined with pneumatic or electric instrument panel. Wide used in metallurgy, mine, petroleum, chemical plant, electric power, light industry, shipyard,etc. Suitable medium is gas, liquid, or flow mingled with solid impurity. It can control by two signals, one is simulation signal, and other one is quantum of opening.
㈠、超高壓大口徑氣動球閥安裝要求
1．可在水平或垂直管道上安裝使用，不受位置限制。
i. The valve can be installed on the pipe line in both level and vertical position.
2．安裝前必須對閥門内腔和密封面進行徹底清掃，不允許有污物粘附，并檢查運輸過程中有無損壞。
ii. Before installation, check the valve, and clear inside and RF surface.
3．安裝前要徹底清掃管道中的(de)污物和焊渣。
iii. Flange connection bolting must be screw down equally.
4．法蘭連接螺栓應對稱均勻擰緊。
iv. Make a clean sweep of dust and weld sinter inside the pipe line.
5．安裝時氣路管線應用壓縮空氣吹掃幹淨，并檢查接頭是否嚴密可靠。
v. For gas pipe line, must totally dry the pipe line before installation. And check the pipe fittings.
㈡、超高壓大口徑氣動球閥調試
輸入開關量信号，檢查動作時間和動作方向是否符合使用要求。
Load the signal, and see if the valve action according to requirement.
㈢、超高壓大口徑氣動球閥使用維護
1．應注意使用的環境溫度為-25℃~+60℃相對濕度≤95%。
i. Installation temperature: Environment temperature: -25℃~+60℃, Relative humidity: ≤95%
2．氣動執行機構使用的(de)儀表空氣應穩定在0.4~0.7Mpa。氣源應經過除塵、脫水、除油等淨化處理。
ii. Pressure of instrument air: 0.4~0.7MPa, the air flow must clean, dry and without oil.
3．檢修
iii. Examine and repair:
①．執行機構的維護保養見KG、KW型驅動器使用說明書。
1. Maintenance of actuator: please see KG, KW model actuator operation menu.
②．球閥的(de)維護保養：
2. Ball Valve Maintenance:
本閥門适于安裝在野外（但儀表、附件例外）因此不需要采取特殊的保養措施。
The valve can be installed out door (Besides instrument, and Accessories), so no need for maintenance.
㈣、超高壓大口徑氣動球閥可能出現的(de)故障及排除方法：
1、閥座密封滲漏：
a) Seats leak:
1．密封面有損傷或污物，必須重新修整，清洗密封面。
i. Dirty or hurt on seats, clean sealing surface first.
2．密封面變形或失效時，更換密封圈。
ii. Distorted seats, must replace with new seats.
3．預緊力不夠，增強彈簧力度。
iii. Tightness of bolting not enough, change the seat springs.
2、閥杆處密封滲漏：
b) Leakage on the Stem:
卸下操作機構、更換O 型密封圈。
Replace“O”ring.
3、中法蘭處滲漏：
c) Leakage on the body seal position:
更換O 型密封圈。
Replace“O”ring.
